Because of the natural obstacles, signals transmitted may take multiple paths and reach destination at different time. As the chip rate is 3.84Mcps leads to time duration 0.26MicroSecs. If the time difference between multipath signal is 0.26 Micro seconds then receiver can separate those signals and combine them.
Technical Notes, White paper and presentation on LTE, GSM, GPRS, EDGE and CDMA network, 3GPP specifications, UTRAN, GERAN and non 3GPP wireless concepts. This blog also covers programming concepts like C and C++, Embedded programming, SNMP Framework, NMS/EMS, Provisioning system, small cell concepts
Thursday, April 28, 2011
Rake receiver and Multipath signal propagation
Power Control
Open loop power control make rough estimate of path loss by means of a downlink beacon signal. This may not be accurate.
Closed loop power control is performed in the uplink; base station performs frequent estimates of the received Signal-to-Interference Ratio (SIR) and compares it to a target SIR. If the measured SIR is higher than the target SIR, the base station will command the mobile station to lower the power; if it is too low it will command the mobile station to increase its power.
Outer loop power control a procedure where target SIR is changed based on signal quality. Based on the quality of radio link measure in the uplink for each user data channel regulates the target SIR.
Closed loop power control is performed in the uplink; base station performs frequent estimates of the received Signal-to-Interference Ratio (SIR) and compares it to a target SIR. If the measured SIR is higher than the target SIR, the base station will command the mobile station to lower the power; if it is too low it will command the mobile station to increase its power.
Outer loop power control a procedure where target SIR is changed based on signal quality. Based on the quality of radio link measure in the uplink for each user data channel regulates the target SIR.
Monday, April 25, 2011
Engineering mode/Field test mode in various mobiles using codes
LG Mobile:
Most of the LG Models have similar field test menu:
Code: 277634#*#
Model : LG CU720 (LG Shine), LG CU575, LG CU500, LG CU400 (many other models)
Code : 3845#*360#
Model: LG CF360(This model has more options in the field test mode like GPS, DRM test menus, Calibration data)
Samsung Mobile:
Code: *#0011#
Model: SGH-A707, SGH-A717, SGH-A727, SGH-i617 and many other models support this code.
Apple iPhone:
Code : *3001#12345#* then press call
Various field test information could be seen under the menus.
Blackberry Mobile:
Code: Menu->Settings->Options->status
This would show some of field test information on blackberry phones.
Nokia Mobile:
Code: *3001#12345#.
Code changes on some of the Model. Some time field test displays as Net monitor in Nokia mobiles. Most of the models like Nokia 12xx, 51xx (except 5125), 61xx, 62xx, 71xx,3285, 63xx are supported with this code. To get out the engineering mode, you need to either dial 00/01 in some models, in some models in net monitor, you many dial 0000.
You contact me if you need more information or field test mode for any other phone/model, I would try to look and get the information back to you.
Most of the LG Models have similar field test menu:
- Version
- Factory Reset
- Device Test
- Port Setting
- Modem Setting
- SIM Test
- IMS Setting
- IM Client ID
Code: 277634#*#
Model : LG CU720 (LG Shine), LG CU575, LG CU500, LG CU400 (many other models)
Code : 3845#*360#
Model: LG CF360(This model has more options in the field test mode like GPS, DRM test menus, Calibration data)
Samsung Mobile:
Code: *#0011#
Model: SGH-A707, SGH-A717, SGH-A727, SGH-i617 and many other models support this code.
Apple iPhone:
Code : *3001#12345#* then press call
Various field test information could be seen under the menus.
Blackberry Mobile:
Code: Menu->Settings->Options->status
This would show some of field test information on blackberry phones.
Nokia Mobile:
Code: *3001#12345#.
Code changes on some of the Model. Some time field test displays as Net monitor in Nokia mobiles. Most of the models like Nokia 12xx, 51xx (except 5125), 61xx, 62xx, 71xx,3285, 63xx are supported with this code. To get out the engineering mode, you need to either dial 00/01 in some models, in some models in net monitor, you many dial 0000.
You contact me if you need more information or field test mode for any other phone/model, I would try to look and get the information back to you.
What is WPS - Wireless Priority Service
WPS means Wireless Priority Service which is priority calling service provided to the subscribers by the operators. This service is add-on service which shall be subscribed by the subscriber. User must be having WPS feature enabled to make the WPS call.
To make WPS call, dial, *272 + Destination Number
Remember you do not need a special cellphone to make WPS call, only need to subscribed to WPS package from operator. Receiver of the WPS call does not need to subscribe for the WPS feature. *272 enables the priority access to local channels, High probability of completion features (HPC). If the terminating end is mobile user the then priority channels are allocated for terminating call.
To make WPS call, dial, *272 + Destination Number
Remember you do not need a special cellphone to make WPS call, only need to subscribed to WPS package from operator. Receiver of the WPS call does not need to subscribe for the WPS feature. *272 enables the priority access to local channels, High probability of completion features (HPC). If the terminating end is mobile user the then priority channels are allocated for terminating call.
Friday, February 11, 2011
What is Assisted GPS - AGPS
Assisted GPS is used to assist the GPS by providing the additional information like visible GPS satellites, reference time, Doppler which would help in GPS acquisition process. This feature intern help faster GPS acquiring time and reducing the GPS power consumption. Also helps in more accurate GPS measurements with more coverage.
Friday, February 4, 2011
Best programming practice: Constant usage in C/C++
Constant:
Constant means read-only. Answer is not complete but still good. Constant can be declared in various way for various needs.
const int a; //Constant (non-modifiable) integer
int const a; //Constant (non-modifiable) integer
const int *a; //pointer to a Constant (non-modifiable) integer
int * const a; //Constant (non-modifiable) pointer to a integer
int const * a const; //Constant (non-modifiable) pointer to constant integer
You can write a program without using a constant keyword which would work without any problem. But writing a program using constant is good practice and dictates user on how to use them based on its behavior.
Constant means read-only. Answer is not complete but still good. Constant can be declared in various way for various needs.
const int a; //Constant (non-modifiable) integer
int const a; //Constant (non-modifiable) integer
const int *a; //pointer to a Constant (non-modifiable) integer
int * const a; //Constant (non-modifiable) pointer to a integer
int const * a const; //Constant (non-modifiable) pointer to constant integer
You can write a program without using a constant keyword which would work without any problem. But writing a program using constant is good practice and dictates user on how to use them based on its behavior.
Best programming practice (C/C++): When and where to use volatile keyword
Main usage of volatile seen in embedded space. Practical use is seen in
1) Memory mapped peripheral registers 2) Global variables modified by ISR routine 3) Global variables modified by multi-threaded environment. In these scenarios values of these variable can change unexpectedly.
Watch out for the below behaviours and first thing to look for is assessing for the need for volatile variables.
Code stops working when
1) Multithreaded environment but works in single process/threads
2) Enable optimization
3) Enable Interrupts
Volatile qualifier will be used when the variable is declared, which tells the compiler that value of the variable can change without any action taken by code.
volatile int myVolatile;
int volatile myVolatile;
What is the difference between two?
If you do not know the answer let me know.
int * volatile myVolatile;
This means volatile pointer to non volatile variable.
int volatile * volatile myVolatile;
Volatile pointer to Volatile variable.
1) Memory mapped peripheral registers 2) Global variables modified by ISR routine 3) Global variables modified by multi-threaded environment. In these scenarios values of these variable can change unexpectedly.
Watch out for the below behaviours and first thing to look for is assessing for the need for volatile variables.
Code stops working when
1) Multithreaded environment but works in single process/threads
2) Enable optimization
3) Enable Interrupts
Volatile qualifier will be used when the variable is declared, which tells the compiler that value of the variable can change without any action taken by code.
volatile int myVolatile;
int volatile myVolatile;
What is the difference between two?
If you do not know the answer let me know.
int * volatile myVolatile;
This means volatile pointer to non volatile variable.
int volatile * volatile myVolatile;
Volatile pointer to Volatile variable.
Subscribe to:
Posts (Atom)